R 24, SIPCOT Industrial Estate, Gummidipoondi – 601201 | 9840062539 / 9962062539 | admin@tejamachinery.in
Mon – Sat  ·  9:00 AM – 5:30 PM
CNC Retrofit & Mechanical Reconditioning

Same Iron.
Smarter Brain.
Built To Run
Another Decade.

We rebuild ageing machines from both ends — the electronic brain (controller, drives, motors, feedback) through retrofit, and the mechanical body (spindle, motion system, bed, hydraulics) through reconditioning — all on the casting you already own. The machine you were about to replace, running like new.

400+
Machines Retrofitted
150+
Flagship Projects
Global
On-Site & Off-Site Service
20+
Years Retrofitting
60-70%
Lower Cost vs New*
Weeks
Not Months, Downtime

*Industry benchmark for retrofit vs. an equivalent new machine — the real number depends on your machine and gets confirmed during assessment.

Teja Machinery Gummidipoondi shop floor with a large boring mill under the EOT crane

How Retrofit Works

Two Machines Living In One Body

Every CNC machine is really two machines welded into one: a heavy iron body — bed, column, spindle, slideways — and an electronic brain that drives it — the controller, motors, drives and wiring. A retrofit leaves the iron alone and rebuilds only the brain. A boring mill from the 1990s can end up running a control platform built this decade without anyone touching its frame or spindle housing.

The Electrical & Electronic Side

  • CNC controller — aging or discontinued unit swapped for a current-generation platform
  • Servo & spindle motors, plus the drive units and amplifiers that power them
  • Position feedback hardware — encoders and resolvers for accurate axis positioning
  • Electrical cabinet, internal wiring, grounding and I/O modules
  • Operator display and the PLC logic running behind it

Most projects don't stop at the brain — the mechanical body wears too. That's reconditioning, covered next.

CNC lathe control panel and cabinet ready for retrofit at Teja Machinery
Flywheel and gear assembly stripped down for reconditioning at Teja Machinery

The Mechanical Side

Same Casting. Rebuilt Mechanics.

The bed, column and housings — the casting body — almost never need replacing. What wears out is everything that moves against it. Reconditioning rebuilds that on the casting you already own, without the cost of a new base structure.

  • Spindle reconditioning — full overhaul or rebuild, restored to original running accuracy
  • Old lead screws converted to ball screws or rack-and-pinion drives for tighter, backlash-free positioning
  • Traditional feed drives replaced with servo motion systems for accurate, repeatable control
  • Bed and slideways refurbished by hand and machine scraping, restoring true flatness
  • Worn casting surfaces built back up with Biplast lining instead of replacing the casting
  • Hydraulic lines renewed and hydraulic motors reconditioned in-house
  • Structural alignment, levelling and height corrections across the full machine

Where It Applies

Built For The Machines Carrying Your Shop

Retrofit and reconditioning both make the most sense on bigger, higher-value machines — where a like-for-like replacement runs into tens of lakhs and the casting body still has years of life left in it. Straight from our project files, here's what we've worked on:

VTL HBM Radial Drilling VMC CNBM VBM HMT -HMC 400M Cylindrical Grinding Lathe Hydralic Press Brake HMC Surface Grinding Universal Drilling HMC 400 Deep Hole Drilling SPM LATHE SURFACE GRINDING PLANO MILLER MILLING MACHINE HMB GEAR HOBBING 9 AXIS SPM CYLINDERICAL GRINDING Bed Milling Gandry Planomiller ANGULAR GRINDING PIN GRINDING

Our Process

Nine Steps, One Machine, Minimal Downtime

Whether the job is control-only, mechanical-only, or both together, it runs through the same site-to-handover sequence. Electrical kits get built off-site wherever possible, so the machine only comes offline for the actual swap.

01
Site Assessment

The mechanical and electrical health of the machine and its parts is checked and assessed on-site.

02
Dismantling

Machine parts are dismantled — each one reconditioned, overhauled or replaced as necessary.

03
Design & Control Selection

Mechanical and electrical design work, plus electronic selection of the control system to match your shop.

04
Refurbishing

Guideways and bedways are refurbished wherever needed to restore true geometry.

05
Off-Site Kit Build

The new cabinet and wiring kit are assembled and tested away from your floor, shortening idle time later.

06
Assembly

All parts are assembled and positioned for accuracy, with wiring completed.

07
Motor & Feedback Swap

New servo and spindle motors go in, alongside encoders that give the controller accurate position feedback.

08
Install & Calibrate

Axis calibration and laser alignment lock in accuracy before the machine runs a single part.

09
Test, Train & Handover

Trial cuts confirm everything machines correctly, followed by operator training and full documentation.

Reconditioned vertical turning lathe ready for retrofit handover
60-70%
Lower Cost Than An Equivalent New Machine*

The Business Case

Why Rebuild Instead Of Replace

  • Costs a fraction of new — industry-wide, a retrofit-plus-recondition typically runs 20-50% of an equivalent new machine's price
  • Back in production in weeks, not the months a new machine order takes to arrive
  • A modern controller runs programs faster and leaves a better finish than decades-old electronics
  • Compensation features in new controls can offset small mechanical wear electronically
  • Opens the door to monitoring dashboards and predictive maintenance — Industry 4.0 on a machine you already own
  • Backed by a parts-and-labour warranty, the same as you'd expect on new equipment
400+
Machines Retrofitted & Reconditioned
150+
Flagship Projects
50+
Corporate Clients
20+
Years, Since 2006

Real Projects

Retrofit & Reconditioning, On Film

Short clips straight off our shop floor — real machines, from teardown to final trial run.

Next Step

Electronics Stuck? Mechanics Worn? Or Ready For A Full Revamp?

Whether it's the controls, the mechanicals, or a full ground-up revamp of the whole machine — send us the make, model and current condition and we'll tell you within days whether it's a strong candidate.

admin@tejamachinery.in